Author Topic: HEATER BLOWER SWITCH REMOVAL  (Read 2147 times)

kfnut

  • Sr. Member
  • ****
  • Posts: 300
    • View Profile
    • Email
HEATER BLOWER SWITCH REMOVAL
« on: October 15, 2011, 05:27:01 PM »
I'M TRYING TO GET TO THE SCREWS HOLDING THE HEATER BLOWER SWITCH BRACKET OUT AND NEED TO REMOVE THE SWITCH TO GET TO THE SCREWS . THE CHROME LOCK NUT THAT HOLDS IT IS SMOOTH AND BEVELED . I CAN;T GET A HOLD ON IT TO UNSCREW IT . ANYONE HAVE A TRICK FOR THIS ?

kfnut

  • Sr. Member
  • ****
  • Posts: 300
    • View Profile
    • Email
Re: HEATER BLOWER SWITCH REMOVAL
« Reply #1 on: October 15, 2011, 08:15:16 PM »
I HAVE A SWITCH ON THE SHELF AND I LOOKED AT IT . IT HAD A FLAT EDGE ON THE THREADED PART OF THE SWITCH WHICH LOCKED IT IN THE MOUNTING BRACKET SO I THOUGHT IT WAS LOCKED FROM TURNING . I WILL TRY WHAT YOU HAVE SUGGESTED . I DID TRY TO TAKE A SMALL BLADE SCREWDRIVER AND PUT IT IN THE SMALL SLOT ABOVE AND BELOW THE SWITCH SHAFT AND TAP IT LIGHTLY WITH A SMALL HAMMER BUT IT DIDN;T MOVE . I WAS AFRAID TO TAP IT TOO HARD . THANKS FOR THE TIP . I WILL LET YOU KNOW IF IT WORKS .

Terry T

  • Hero Member
  • *****
  • Posts: 1222
  • EX--Editor Darrin Newsletter/Registry
    • View Profile
    • Email
Re: HEATER BLOWER SWITCH REMOVAL
« Reply #2 on: October 16, 2011, 07:19:33 AM »
Make a tool to use on the bezel.
Start with a small thin-wall metal tube that has an ID slightly larger than the diameter of the shaft, and longer of course.
Use a grinder/Dremel to remove metal so that two prongs the size of the slots in the bezel  remain (180 deg. apart).
Use pliers to turn the tool or fashion a handle with a small rod inserted crossways thru the tube.
Got it??

kfnut

  • Sr. Member
  • ****
  • Posts: 300
    • View Profile
    • Email
Re: HEATER BLOWER SWITCH REMOVAL
« Reply #3 on: October 16, 2011, 07:27:12 AM »
THANKS . I AM GOING TO TRY BOTH SUGGESTIONS AS SOON AS POSSIBLE . CAN'T DO IT TODAY AS I HAVE TO GO TO FUNERAL ABOUT 3 1/2 HOURS AWAY BUT WILL TRY MONDAY .
THANKS

Corsairdeluxe

  • Hero Member
  • *****
  • Posts: 811
    • View Profile
    • Email
Re: HEATER BLOWER SWITCH REMOVAL
« Reply #4 on: October 16, 2011, 10:29:29 AM »


A snap ring tool works perfectly and you will need one eventually. Not expensive.

http://www.ebay.com/itm/4-in-1-Snap-Ring-Pliers-Combination-Interchangable-/320776259413?pt=Pliers&hash=item4aafc14755
Jim Brown aka Corsairdeluxe
#3559
10 Henrys and 1 ALLSTATE
behind me. J less at the moment and having irrational thoughts.

kfnut

  • Sr. Member
  • ****
  • Posts: 300
    • View Profile
    • Email
Re: HEATER BLOWER SWITCH REMOVAL
« Reply #5 on: October 17, 2011, 07:11:29 PM »
O.K.  I GOT IT OFF . I TRIED THE SNAP RING PLIERS TRICK THE OTHER DAY BUT FORGOT TO MENTION IT. I TRIED SEVERAL SIZES OF 90% SETS AND THEN SOME STRAIGHT ONES . WHILE DRIVING FOR 7 HOURS AND THINKING ABOUT IT I TRIED TWO SMALL BLUNT TIPED PUNCHES STUCK STRAIGHT INTO THE TWO SMALL SLOTS . THEN TOOK AN ADJUSTABLE WRENCH CLOSED TIGHT ON THE PUNCHES . IT WORKED . I WANT TO THANK EVERYONE FOR THEIR HELP .

Fid

  • Hero Member
  • *****
  • Posts: 3858
    • View Profile
    • Email
Re: HEATER BLOWER SWITCH REMOVAL
« Reply #6 on: October 17, 2011, 07:37:16 PM »
Congratulations, that's good news. I'm glad you got it off intact.
1953 Henry J Corsair Deluxe
Edgar Kaiser's custom 1951 Henry J
1951 Kaiser Special
1952 Allstate Deluxe

Need your classic car radio repaired? I repair vacuum tube radios