Author Topic: Rocker cover stud gaskets  (Read 1252 times)

MarkH

  • Hero Member
  • *****
  • Posts: 1083
    • View Profile
    • Email
Rocker cover stud gaskets
« on: July 13, 2017, 08:08:59 PM »
Anyone know of a source for these rocker cover stud gaskets?
I found these on mercadolivre but need at least 2 more.
They're a very dense hard rubber and keep the bolts centered in the rocker cover holes.
The ones included in an Egge gasket set are just flat gasket paper washers.
Fully restored '54 Aero Lark
Rusty '58 Austin Healey 100-Six
Barely running'74 Chevelle Malibu

njpatera

  • Hero Member
  • *****
  • Posts: 502
    • MSN Messenger - pateraclass@msn.com
    • View Profile
    • Email
Re: Rocker cover stud gaskets
« Reply #1 on: July 14, 2017, 09:26:35 AM »
If needed...could you use one from a Y-block?
Regards,
Noah

'54 Darrin
'55 Victoria
'56 Victoria
-'59 Galaxie/Fairlane Convert.
'61 Falcon 2dr wagon
-'62 Galaxie 500XL Convertible

Member #5954
The Nifty Fifties NE Ohio
Drummer: Moving in Stereo, Cleveland’s Tribute to The CARS

MarkH

  • Hero Member
  • *****
  • Posts: 1083
    • View Profile
    • Email
Re: Rocker cover stud gaskets
« Reply #2 on: July 14, 2017, 01:34:09 PM »
If needed...could you use one from a Y-block?

I've seen several similar gaskets for a variety of vehicles but so far none proven to fit an Aero rocker cover hole & stud. These are a very dense hard rubber, I suspect to withstand the compression force to properly seal the large cover to head perimeter gasket. The 1952 engine repair manual states these are made of a soft metal.
Fully restored '54 Aero Lark
Rusty '58 Austin Healey 100-Six
Barely running'74 Chevelle Malibu

MarkH

  • Hero Member
  • *****
  • Posts: 1083
    • View Profile
    • Email
Re: Rocker cover stud gaskets
« Reply #3 on: July 14, 2017, 05:52:29 PM »
I checked an early '52 engine I have and did find metal gaskets mentioned in the '52 manual, and rocker cover stud holes just big enough to clear the stud.

Quite different from the later US or Brazilian version.
Fully restored '54 Aero Lark
Rusty '58 Austin Healey 100-Six
Barely running'74 Chevelle Malibu

joefrazer

  • Hero Member
  • *****
  • Posts: 4042
    • View Profile
Re: Rocker cover stud gaskets
« Reply #4 on: July 14, 2017, 06:35:04 PM »
I've torn apart several f-heads over the years and have never seen these seals. All have had either flat rubber baskets or metal flat washers in place.

I just took apart my Darrin engine - it had never been open - and it has flat rubber gaskets.

MarkH

  • Hero Member
  • *****
  • Posts: 1083
    • View Profile
    • Email
Re: Rocker cover stud gaskets
« Reply #5 on: July 14, 2017, 10:36:37 PM »
I've torn apart several f-heads over the years and have never seen these seals. All have had either flat rubber baskets or metal flat washers in place.

I just took apart my Darrin engine - it had never been open - and it has flat rubber gaskets.

The Brazilian ones pictured are definitely thicker than the ones that were in my "early" '54 F-head, but they did have a wider top flange than the "bolt centering" bottom. At 28K miles when I got it, (now 45k) I couldn't say whether or not the engine was ever opened to do valve adjustment maintenance, especially after the machinist mentioned the recommendation used to be to adjust valves every spring. I know it never got it after 28K, and it showed on the rocker faces.
Fully restored '54 Aero Lark
Rusty '58 Austin Healey 100-Six
Barely running'74 Chevelle Malibu

MarkH

  • Hero Member
  • *****
  • Posts: 1083
    • View Profile
    • Email
Re: Rocker cover stud gaskets
« Reply #6 on: August 21, 2017, 08:27:38 AM »
     
  Seal kit listed in the '54/'55 parts list supplement booklet.
Fully restored '54 Aero Lark
Rusty '58 Austin Healey 100-Six
Barely running'74 Chevelle Malibu