Author Topic: Alternator install  (Read 3494 times)

jap tin

  • Jr. Member
  • **
  • Posts: 58
    • View Profile
    • Email
Alternator install
« on: September 24, 2012, 12:57:03 PM »
I ordered a 6 volt positive ground alternator to go on the 52 J.
I'm getting a 2.6" dia pulley to go on it
Any tips or tricks I should know about?

HJ-ETEX

  • Hero Member
  • *****
  • Posts: 640
    • View Profile
    • Email
Re: Alternator install
« Reply #1 on: September 24, 2012, 06:16:59 PM »
Well, it is good you are being thorough in ordering a pulley. However, you may want to look at pulley that was on the 6V generator.
When I put a 12V GM 10SI on my 1951 CJ3A, I took the pulley off the original generator.
Also you haven't even mentioned a mounting bracket.
KFOCI VP 2001-2005
1951 Kaiser Deluxe /327 Chevy
1951 Kaiser Deluxe (no funny stuff)
1968 Kaiser Commando V6
1961 Willys 2WD 134 F-Head SW
1963 Kaiser FC170

jap tin

  • Jr. Member
  • **
  • Posts: 58
    • View Profile
    • Email
Re: Alternator install
« Reply #2 on: September 24, 2012, 06:58:15 PM »
I figured I would have to fab a bracket to mount the alternator. Shouldn't be too bad there. I went with a smaller 1/2"  wide pulley to get the rpm up on the alternator at idle and the belt would match the waterpump and crank pulley. I figured the little flat head 4 wouldn't be much of a rpm monster so it won't hurt to spin the alternator a little faster.

darrin145

  • Full Member
  • ***
  • Posts: 244
    • View Profile
    • Email
Re: Alternator install
« Reply #3 on: September 25, 2012, 07:30:39 AM »
Where did you order the pulley from? I need one for one of my cars and have had little luck finding one. Thanks!

Gary.

jap tin

  • Jr. Member
  • **
  • Posts: 58
    • View Profile
    • Email
Re: Alternator install
« Reply #4 on: September 25, 2012, 08:50:42 AM »
I got it from the guy that I got the alternator from. 110953076077. His name is Kevin Weust.
They are on e-bay from various sources. Here is one, 190618208217 is the item number, search this one on e-bay.

darrin145

  • Full Member
  • ***
  • Posts: 244
    • View Profile
    • Email
Re: Alternator install
« Reply #5 on: September 25, 2012, 09:07:46 AM »
Thanks for the info, it just might work!

Gary.

Corsairdeluxe

  • Hero Member
  • *****
  • Posts: 811
    • View Profile
    • Email
Re: Alternator install
« Reply #6 on: September 30, 2012, 08:47:17 AM »
I put a 6 volt positive ground alternator, 60 amps,with a small pulley on my J and an Optima battery  . I was GREAT. Would do it again in a minute. You can fabricate a mount from angle braces from the home depot or you can just by one.

http://jimcotest.com/index.php?option=com_content&view=article&id=21&Itemid=23&lang=en

A bit of a warning. Some 6 volt alternators sold on ebay are made by clipping diodes on a 12 volt delco 10si. It gives you 6 volts but only 30 amps and that is not worth the effort.

Jim Brown aka Corsairdeluxe
#3559
10 Henrys and 1 ALLSTATE
behind me. J less at the moment and having irrational thoughts.

Corsairdeluxe

  • Hero Member
  • *****
  • Posts: 811
    • View Profile
    • Email
Re: Alternator install
« Reply #7 on: September 30, 2012, 08:51:31 AM »
Jim Brown aka Corsairdeluxe
#3559
10 Henrys and 1 ALLSTATE
behind me. J less at the moment and having irrational thoughts.

jap tin

  • Jr. Member
  • **
  • Posts: 58
    • View Profile
    • Email
Re: Alternator install
« Reply #8 on: September 30, 2012, 10:29:29 PM »
I fabed the alt bracket today. Got some 8 gauge fine wire cable for the alt power line. Found the water pump weaping so a new water pump is on the way.

jap tin

  • Jr. Member
  • **
  • Posts: 58
    • View Profile
    • Email
Re: Alternator install
« Reply #9 on: October 04, 2012, 06:37:10 PM »
New waterpump, heater shutoff valves and hoses. Fired it up and the one wire alternator was putting 25 amps at idle, 6.9 volts. Much better than the old generator.  :)